Theben 4940301 User Manual Download Page 29

Page: 29 / 88

ETS communication objects

Manual DALI gateway S64 KNX/S128 KNX

80a

G1, Failure Exceeds

Threshold

Yes/No

1 Bit

1.005

CRT

This object is used to report that the total of all lamps, ECG and converter failures found within

the group exceeds the threshold set via parameters.
80b

G1, Failure Rate in Total

Value

1 Byte

5.010

CRT

The total number of light and ECG errors within the group is reported via this object.

80c

G1, Failure Rate in %

Value

1 Byte

5.001

CRT

This object is used to report the error rate as a percentage of the total number of devices

within the group.
Object 95-97 will be displayed on: G1



Analysis and Service



Operating Hour Calculation

G1, Operating Hours Reset

Yes/No

1 Bit

1.015

The operating hours within the group can be reset with „1“ via this object.

G1, Operating Hours

Value

4 Byte

13.100

Counts the operating hours in the group. This value is transmitted in seconds according to DTP

13.100.
97

G1, Life Time Exceeded

Yes/No

1 Bit

1.005

This object shows whether the maximum life span set in the parameters has been exceeded.

Note

: If the treshold has been exceeded, an alarm is issued via this object (by sending “1“).

This status is resent for each further hour that is above the threshold.

Objects for colour control

Different colour control options are supported:

•

Colour temperature

•

RGB

•

HSV

•

RGBW

•

Only one type of colour control can be selected for a group. All ECGs in the group that support

this type can thereby be controlled. Other ECG types will not react to the command. Please

remember to only assemble ECGs with the same colour control in a group.

Colour temperature

Depending on the type of colour control, different objects are shown:

Figure 3: Colour temperature (Source: Wikipedia)

Summary of Contents for 4940301

























































































Search results

Summary of Contents for 4940301

Reviews:

Related manuals for 4940301

Brands by name

Popular brands

Theben 4940301, User Manual

Search results

Summary of Contents for 4940301

Reviews:

Related manuals for 4940301

Brands by name

Popular brands