Theben 4940301 User Manual Download Page 56

Page: 56 / 88

ETS parameters

Manual DALI gateway S64 KNX/S128 KNX

Parameter

Settings

ECG x, Description

e.g.: Floor, 1 level

With this parameter an ECG description can be defined. This description is displayed as an

overview for all communication objects. Example for the description: Floor, 1 level.

Group Assignment

Not assigned

Group 1

…

Group 16

The group assignment is configured via the DCA or via the website and is only displayed here.

ECG Type

Fluorescent Lamp

Self Contained Battery Lamp (non switchable)

Self Contained Battery Lamp (switchable)

Discharge Lamp

Low Voltage Lamp

Incandescent Lamp

0..10V Converter

LED Module

Relay Module

ECG with Colour Control

Use this parameter to set the type of ECG used.

Operating Mode

Normal Mode

Permanent Mode

Normal / Night Mode

This parameter allows to set the operating mode in which the ECG shall be operated. Night

operation is controlled via a central object no. 12.
Function of Additional Objectt

No Obejct

Disable Object

Release Object

This parameter can be used to define the function of an additional object. If the "Disable

object" is selected, an object is displayed which blocks operation of the ECG if the value is "1".

If the "Enable object" is selected, an object is displayed which enables operation of the ECG if

the value is "1".

Note:

Disable function only refers to ON/OFF and value setting commands via KNX objects

Behaviour on Enable

No Chance

Switch to ON-Value

Switch to OFF-Value

This parameter is displayed when an additional object is selected. The behaviour during

activation can be defined here..
Behaviour on Disable

No Chance

Switch to ON-Value

Switch to OFF-Value

This parameter is displayed when an additional object is selected. The behaviour during

deactivation can be defined here..
Value in Permanent Mode

1..100%

[50%]

Summary of Contents for 4940301

























































































Search results

Summary of Contents for 4940301

Reviews:

Related manuals for 4940301

Brands by name

Popular brands

Theben 4940301, User Manual

Search results

Summary of Contents for 4940301

Reviews:

Related manuals for 4940301

Brands by name

Popular brands