Teltone TSP Edge User Manual Download Page 159

Page: 159 / 177

TSP Edge User’s Manual

40-400-00065, Rev. E

149

T1/E1 Primary Rate (CPE) - Call Originate

Seizure from Edge.

Wait For Answer

timer starts.

Edge detects answer from equipment under test.

Call Duration

timer starts.

Delay Before Message

timer starts.

NOTE: If

Wait for Answer

timer expires before the Edge detects

answer from equipment under test, the Edge will proceed to step 6.

Delay Before Message

timer expires.

Edge starts playing audio message.

Edge detects on-hook from equipment under test.

Disconnect to start of new call

timer starts.

Note: If

Call Duration

timer expires before detecting on-hook from

the equipment under test, the Edge will disconnect first.

Disconnect to start of new call

timer expires.

Edge ready to receive next call.

If no Audio Message is programmed for the channel, proceed directly to step 3.

Wait For

Answer

Delay Before

Message

TSP Plays

Audio

Message

Disconnect
To Start Of

New Call

Call

Setup

Call Connected

Call

Disconnect

Summary of Contents for TSP Edge


















































































































































































Search results

Summary of Contents for TSP Edge

Reviews:

Related manuals for TSP Edge

Brands by name

Popular brands

Teltone TSP Edge, User Manual

Search results

Summary of Contents for TSP Edge

Reviews:

Related manuals for TSP Edge

Brands by name

Popular brands