Teltone TSP Edge User Manual Download Page 115

Page: 115 / 177

TSP Edge User’s Manual

40-400-00065, Rev. E

105

Tones/Audio

This tab has the command buttons for enabling detectors and sending tones and Wave
files.

For detecting DTMF, Broadband or Voice, the detectors have to be enabled and then
disabled. The following sequence of commands should happen:

1. The appropriate detector must be enabled prior to the event using the

Detect Enable

commands.

2. A

Wait For Event(s), Detector Available

must follow to wait until the

detector is ready to receive.

3. An

command verifies the detector is available.

4. Another

Wait For Events(s), Detect Seen

waits for the audio signal.

5. Another

statement determines what tone was seen and determines the

next command accordingly.

6. A

Detect Disable

command disables the detector.

Figure 48 shows the sequence for Detecting DTMF.

Summary of Contents for TSP Edge


















































































































































































Search results

Summary of Contents for TSP Edge

Reviews:

Related manuals for TSP Edge

Brands by name

Popular brands

Teltone TSP Edge, User Manual

Search results

Summary of Contents for TSP Edge

Reviews:

Related manuals for TSP Edge

Brands by name

Popular brands