Teltone TSP Edge User Manual Download Page 155

Page: 155 / 177

TSP Edge User’s Manual

40-400-00065, Rev. E

145

E1 ITU Q.421 - Call Originate

Seizure from Edge.

Wait for Seize Acknowledge

timer starts.

Seize acknowledge received from equipment under test.

Delay before Dialing

timer starts.

Note: If

Wait for Seize Acknowledge

timer expires before acknowledge

received from equipment under test, the Edge will release the seizure and
proceed to step 7.

Delay before Dial

timer expires.

Edge starts dialing

the Transmit Digits assigned to channel

Dialing ends.

Wait For Answer

timer starts.

Edge detects answer from equipment under test.

Call Duration

timer starts.

Delay Before Message

timer starts.

Note: If

Wait for Answer

timer expires before the Edge detects answer from

equipment under test, the Edge will proceed to step 7.

Delay Before Message

timer expires.

Edge starts playing audio message.

Edge detects on-hook from equipment under test.

Far-end Disconnect

timer starts.

Note: If

Call Duration

timer expires before detecting on-hook from the

equipment under test, the Edge will send 850ms COD.

Far-end disconnect

timer expires.

Disconnect to start of new call

timer starts.

Note: If equipment under test goes back off-hook before the

Far-End

Disconnect

timer expires, the Edge goes back to looking for step 6.

Disconnect to start of new call

timer expires.

Edge ready to receive next call.

DTMF dialing uses the DTMF Transmit Length timing for both the on and off times.

If no Audio Message is programmed for the channel, proceed directly to step 6.

Call Setup

Call Connected

Call Disconnect

Delay Before

Dial

Wait For

Seize

Acknowledge

Wait For

Answer

Delay Before

Message

TSP Plays

Audio

Message

Disconnect
To Start Of

New Call

TSP Dials

Far-End Disconnect

guard time -

Calling Party Control

Summary of Contents for TSP Edge


















































































































































































Search results

Summary of Contents for TSP Edge

Reviews:

Related manuals for TSP Edge

Brands by name

Popular brands

Teltone TSP Edge, User Manual

Search results

Summary of Contents for TSP Edge

Reviews:

Related manuals for TSP Edge

Brands by name

Popular brands