Teltone TSP Edge User Manual Download Page 9 | Manualshive

Page: 9 / 177

background image

40-400-00065, Rev. E

ix

IMPORTANT USER SAFETY INSTRUCTIONS

When using this product, basic safety precautions, including the following, should always be followed to reduce the risk of fire,
electric shock, and injury to persons.

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. The product should be operated only from the type of power source indicated on the marking label. If you are not sure of the

type of power supply, consult your dealer or local power company. The product is designed for indoor use only.

4. To reduce the risk of electric shock, do not disassemble the product, but take it to qualified service personnel when service or

repair work is required. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect reassembly
can cause electric shock when the appliance is subsequently used.

5. If the product does not operate normally by following the operating instructions, or if the product has been dropped or the

cabinet has been damaged, or if the product exhibits a distinct change in performance, refer servicing to qualified service
personnel.

6. If the product is used in a manner other than specified in this manual, the protection provided by the product may be impaired.

7. For the purpose of removing power from the product, the power input connector is the main power disconnect point. Pull the

power cord away from the connector to ensure power disconnect.

8. Adequate air flow must be maintained in order for the product to operate correctly. Do not wrap the product in blankets, paper,

or other material that may impede ventilation.

«
...
7
8
9
10
11
...
»

Summary of Contents for TSP Edge


















































































































































































Reviews:

No comments

Related manuals for TSP Edge

Netlink FRX4000

Brand: Cabletron Systems Pages: 8

Brand: Cabletron Systems Pages: 4

MMAC-Plus 9F106-02

Brand: Cabletron Systems Pages: 7

Transportation FiberinMotion

Brand: Radwin Pages: 122

ZyXEL EES-1024AF

Brand: ZyXEL Communications Pages: 99

Brand: Davey Pages: 18

Brand: Campbell Pages: 38

Wisenet PRN-6400B4

Brand: Hanwha Techwin Pages: 14

Brand: ZALMAN Pages: 9

Procont LMC-008-IO

Brand: janitza Pages: 28

Brand: Keithley Pages: 98

Brand: ICP DAS USA Pages: 62

Brand: Dataprobe Pages: 5

SinoCon C2000-C2-SHK0401-BB1

Brand: KonNad Pages: 12

Brand: Accton Technology Pages: 78

Brand: M-system Pages: 4

Brand: Kramer Pages: 56

Brand: Kasda Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands