Teltone TSP Edge User Manual Download Page 31 | Manualshive

Page: 31 / 177

background image

TSP Edge User’s Manual

40-400-00065, Rev. E

21

Network Connection

A network connection can be used for programming and controlling the Edge, and for
downloading audio files and software upgrades to the unit. It

must

be used when a

T1/E1 module is programmed for T1-PRI or E1-PRI mode to allow for enhanced
messaging. The initial setup of the IP address for the network connection must be
done from the Network tab on the Unit screen via the serial connection. The Network
tab is used to assign a new IP address or to change an existing IP address (see
“Changing an IP Address” on page 22).

The IP Address field on the General tab displays the IP address of the currently
connected unit. The field is also used to connect to units that have already been
assigned an IP address. Even if the serial connection is used for controlling the unit,
the Ethernet connection is still required if using audio files or downloading newer
version software.

To configure the IP address, ensure you have connected the unit’s Ethernet port either
to the LAN with a straight-through cable or to the PC directly using the crossover
cable provided.

If connecting to a LAN, contact your network administrator to assign a static IP for
the unit.

To enter the IP address, go to the Units menu, click the unit name and select the
Network tab on the Unit screen. Use a valid IP format that is in the same subnet and
uses a valid subnet mask. Click OK.

Network Control

A network connection can be used for controlling the Edge. Only a PC on the same
subnet as the unit can control it via the network.

To enable network control, select the unit on the Units menu. On the Unit screen
General tab, the IP address programmed into the unit will be displayed. Select
Network connection and click OK. The unit is controlled via the Ethernet connection
at this point.

If the unit’s IP address is not displayed on the Unit screen, follow the instructions in
the previous subsection first.

Connecting to a Unit on the Network

You can connect your PC to any Edge that has been assigned a valid IP address and is
on the network. The Edge configuration software remembers the names and IP
addresses of all the units that your PC has connected to.

If your PC has previously connected to the unit, select New on the Units menu. In the
New Unit dialog box, select the unit you wish to connect to. This automatically enters

«
...
29
30
31
32
33
...
»

Summary of Contents for TSP Edge


















































































































































































Reviews:

No comments

Related manuals for TSP Edge

Brand: D-Link Pages: 99

Brand: D-Link Pages: 5

Brand: D-Link Pages: 15

AirPro DWL-6000AP

Brand: D-Link Pages: 65

DES-3526 - Switch - Stackable

Brand: D-Link Pages: 258

Brand: Paradyne Pages: 112

Brand: Cambium Networks Pages: 215

Brand: Google Pages: 14

Brand: EVOC Pages: 57

Brand: Netis Pages: 16

Brand: Comelit Pages: 19

Brand: Z-Com Pages: 18

5200 Live Series EventCD

Brand: MF DIGITAL Pages: 21

Open Standard Module RPX30 EVA-MI V1

Brand: iesy Pages: 9

Brand: Teridian Pages: 2

Brand: CyberResearch Pages: 59

Brand: LevelOne Pages: 83

Brand: Qlogic Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands