Teltone TSP Edge User Manual Download Page 19

Page: 19 / 177

TSP Edge User’s Manual

40-400-00065, Rev. E

Delivery of Called and Caller number (CLIP)

Delivery of Type of Address and Numbering Plan

TSP-2PRI

The TSP-2PRI software module adds either T1 or E1 Primary Rate ISDN to an Edge
unit that already has one of the two types installed.

TSP-ATS

TSP-ATS

(Advanced Test Scripting): This software module includes the standard

Edge features plus user defined scripts including:

•

User-definable call sequences

•

Send DTMF during a call

•

Detect DTMF during a call

•

Send test tones

•

Detect broadband energy

•

Detect voice

•

Play multiple wave files on a channel

License Codes

Edge license codes are used for:

•

Enabling additional purchased software modules

•

Setting warranty information

For information about upgrading the Edge, see “Upgrades Tab” on page 48.

SETUP

System Requirements

Power

Caution:

AC operating power must be within 90 to 250 volts AC and the

operating frequency from 43 to 63 Hz.

The Edge unit uses an industry standard IEC three prong connector so that almost any
international power cord can be used. A standard North American power cord is
provided with the unit.

Summary of Contents for TSP Edge


















































































































































































Search results

Summary of Contents for TSP Edge

Reviews:

Related manuals for TSP Edge

Brands by name

Popular brands

Teltone TSP Edge, User Manual

Search results

Summary of Contents for TSP Edge

Reviews:

Related manuals for TSP Edge

Brands by name

Popular brands