Teltone TSP Edge User Manual Download Page 122 | Manualshive

Page: 122 / 177

background image

TSP Edge User’s Manual

40-400-00065, Rev. E

112

TROUBLESHOOTING

If your question is not answered below, please check the FAQs on the Teltone
website (

www.teltone.com

).

Icon:

Problem:

Error message “Communication error to unit ‘name’ Transmit Failure”

Solution:

1. Check that the Edge is powered up and running.

2. Check the console connection. The console cable should connect

between the Console jack on the Edge and a serial port on the PC, using
a DB9 or DB25 adapter.

3. Check the Unit definition. The definition for the Edge you are

attempting to communicate with should define the same serial port
which you are using to connect to the Edge.

4. Initialize the Edge. Select Initialize on the Units menu, and select the

name of the unit you are attempting to connect to.

Any time there is a communication error to the Edge, you MUST INITIALIZE
the Edge to re-establish the connection. On the PC software go to

Units

,

Initialize

, and select the name of the unit you are attempting to connect to.

Initialization takes place automatically if you edit a Unit. Any Control Sets
which were active within that unit will need to be disabled and then re-enabled.

Problem:

Error message “Cannot connect to unit ‘name’. Serial port already in use by
‘name’.”

Solution:

Two or more Units within the current project are defined to use the same serial
port connection. Edit one of the Units and assign a different serial port.

Any time there is a communication error to the Edge, you MUST INITIALIZE
the Edge to re-establish the connection. On the PC software go to

Units

,

Initialize

, and select the name of the unit you are attempting to connect to.

Initialization takes place automatically if you edit a Unit. Any Control Sets
which were active within that unit will need to be disabled and then re-enabled.

«
...
120
121
122
123
124
...
»

Summary of Contents for TSP Edge


















































































































































































Reviews:

No comments

Related manuals for TSP Edge

Express EtherNetwork DFE-670TXD

Brand: D-Link Pages: 4

Brand: DAD Pages: 36

Brand: D-Link Pages: 2

Brand: Abocom Pages: 11

Brand: Abocom Pages: 19

UR5i v2 Libratum

Brand: B+B SmartWorx Pages: 8

Brand: B+B SmartWorx Pages: 8

Brand: National Instruments Pages: 26

Brand: National Instruments Pages: 85

Module SCXI-1503

Brand: National Instruments Pages: 79

Brand: Parkside Pages: 55

Brand: Parkside Pages: 34

SAFETank Series

Brand: Raidon Pages: 49

Brand: Usr Pages: 2

Proventia A1204

Brand: Internet Security Systems Pages: 42

Brand: Renesas Pages: 941

HBJC924R3288DG2NS Series

Brand: JETWAY Pages: 6

Brand: H3C Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands