manualshive.com logo in svg

Teledyne 200A, Instruction Manual, Page: 75 / 220

Share
Download
Teledyne 200A Instruction Manual Download Page 75

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

Table 5-18:  RS-232 Calibration Examples 

Action 

RS-232 Commands 

Comments 

Zero Calibration 

C ZERO 
C COMPUTE ZERO 
C EXIT 

Z/S valves switched to admit 
zero gas. Zero cal in Single 
Range mode. 

Zero Calibration of low range - 
AutoRange Enabled 

C ZERO 1 
C COMPUTE ZERO 
C EXIT 

Z/S valves switched to admit 
zero gas. Zero calibration of 
low range in Auto Range 
mode. 

Span Calibration of high range - 
AutoRange Enabled 

C SPAN 2 
C COMPUTE SPAN 
C EXIT 

Z/S valves switched to admit 
span gas. Span calibration of 
high range in Auto Range 
mode. 

Zero Calibration with Dynamic 
Calibration enabled 

C ZERO 
C EXIT 

Z/S valves switched to admit 
zero gas. Instrument is zero 
calibrated if DYN CAL is 
enabled. 

Zero Calibration  

C ZERO 
C EXIT 

Z/S valves switched to admit 
zero gas. Instrument zero is 
just checked, but not changed. 

Execute AutoCal Sequence #2 

C ASEQ 2 

Execute a predefined AutoCal 
Sequence. Executes sequence 
immediately, ignoring time and 
date parameters. 

Span Calibration Check 

C SPAN 
C EXIT 

Z/S valves switched to admit 
span gas. Instrument span is 
just checked, but not changed. 

 

Whenever the analyzer starts or finishes an IZS calibration, it issues a status report to the RS-232 
interface. If the RS-232 interface is in the normal mode, these reports will be sent. Otherwise, 
they will be discarded. Table 5-19 shows the format of the text of the calibration messages. An 
example of an actual sequence of calibration status messages is:

 

C DDD:HH:MM IIII START MULTI-POINT CALIBRATION 

C DDD:HH:MM IIII NOX=xxxxx PPB NO=xxxxx PPB NO2=xxxxx PPB 

C DDD:HH:MM IIII FINISH MULTI-POINT CALIBRATION 

5-35 

Summary of Contents for 200A





























































































































































































































Reviews:

No comments