manualshive.com logo in svg

Teledyne 200A, Instruction Manual, Page: 170 / 220

Share
Download
Teledyne 200A Instruction Manual Download Page 170

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

9.2.3  No Response to Sample  

1.

 

Confirm correct operation of analog output by performing Analog Output Step Test in 

Section 9.1.3.5. 

2.

 

Confirm general operation of analyzer. 

A.

 

Check for AC Power, Section 9.2.1. 

B.

 

Do flow checks, Section 9.2.2. 

C.

 

Confirm that sample gas contains NO or NO

2

. 

3.

 

Check instrument electronics. 

A.

 

Do ELEC TEST procedure in DIAGNOSTIC menu Section 9.1.3.2. 

B.

 

Do OPTIC TEST procedure in the DIAGNOSTIC menu Section 9.1.3.3. 

 
If the M200A passes ET and OT, that means the instrument is capable of detecting light 
and processing the signal to produce a reading. Therefore, the problem is in the 
pneumatics or ozone generator. 

4.

 

Check ozone generator subsystem. Do diagnostic test of ozone generator subsystem, see 

Section 9.3.6. 

5.

 

Check for disconnected electrical cables to sensor module. 

9-28 

Summary of Contents for 200A





























































































































































































































Reviews:

No comments