manualshive.com logo in svg

Teledyne 200A, Instruction Manual, Page: 112 / 220

Share
Download
Teledyne 200A Instruction Manual Download Page 112

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

Plot the analyzer NO and NO

x

 responses versus the corresponding calculated concentrations to 

obtain the calibration relationships. Determine the straight line of best fit (y = mx + b) 
determined by the method of least squares. 

After the best-fit line has been drawn for the NO and the NO

x

 calibrations, determine whether 

the analyzer response is linear. To be considered linear, no calibration point should differ from 
the best-fit line by more than 2% of full scale.  

7.8.5.3  GPT - NO

2

 Calibration Procedure 

The M200A computes the NO

2

 concentration by subtracting the NO from the NO

x

 concentration. 

Unlike analog instruments, this difference is calculated by the M200A's internal computer 
software. It is extremely unlikely that the NO

2

 concentration will be in error. Therefore this 

procedure is a confirmation that the NO

2

 subtraction algorithm in the computer is operating 

correctly. 

NOTE 

During this procedure do not make any adjustments to the instrument. 

 

1.

 

Generate an NO concentration near 90% of the URL. Dilution air and O

3

 generator air 

flows should be the same as used in the calculation of specified conditions of the dynamic 
parameter according to Section 7.8.4. Sample this NO concentration until the NO and NO

x

 

responses stabilize. Record the NO and NO

x

 concentrations. 

2.

 

Turn on and adjust the O

3

 generator in the calibrator to produce sufficient O

3

 to decrease 

the NO concentration to about 10% of full scale. This will be equivalent to 80% of the URL 
of the NO

2

 channel. After the analyzer responses stabilize, record the resultant NO, NO

x

, and 

NO

2

 concentrations. 

 
MOLY CONVERTER EFFICIENCY 
 
IF THE NO

x

 READING SHOULD DROP TO LESS THAN 96% OF ITS STARTING 

VALUE DURING THIS STEP, IT INDICATES THE MOLY CONVERTER IS IN NEED 
OF TROUBLESHOOTING OR REPLACEMENT. SEE SECTION 7.8.6 FOR FURTHER 
DETAILS. 

3.

 

While maintaining all other conditions, adjust the ozone generator to obtain several other 

concentrations of NO

2

 evenly spaced between the 80% URL point and the zero point. Record 

the NO, NO

x

, and NO

2

 concentrations for each additional point. 

7-24 

Summary of Contents for 200A





























































































































































































































Reviews:

No comments