manualshive.com logo in svg

Teledyne 200A, Instruction Manual, Page: 14 / 220

Share
Download
Teledyne 200A Instruction Manual Download Page 14

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

 

WARNING 

Analyzer Exhaust – O

3

 Scrubber – Pump  

Pack Danger – Analyzer exhaust contains ozone. 

Ozone scrubber must always be present  

between analyzer exhaust and pump. 

Vent pump exhaust to well ventilated area at atmosphere  

pressure FIRE or EXPLOSION HAZARD. 

Do not use charcoal treated with halogen compounds –  

use only Teledyne API P/N 00596 charcoal. 

 

Wait at least 5 minutes after turning off pump  

before removing ozone scrubber WARNING. 

 

WARNING 

Lethal voltages present inside case. 

Do not operate with cover off during normal operation. 

Before operation check for correct input  

voltage and frequency. 

Do not operate without proper chassis grounding. 

Do not defeat the ground wire on power plug. 

Turn off analyzer power before disconnecting  

electrical subassemblies. 

 

2-2 

Summary of Contents for 200A





























































































































































































































Reviews:

No comments