manualshive.com logo in svg

Teledyne 200A, Instruction Manual, Page: 142 / 220

Share
Download
Teledyne 200A Instruction Manual Download Page 142

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

8.10  Light Leak Check Procedure 

1.

 

Scroll the TEST functions to PMT. 

2.

 

Input zero gas. 

3.

 

Shine a powerful flashlight or portable incandescent light at the inlet and outlet fitting, 

and at all the joints of the reaction cell. The PMT value should not respond to the light.  

If there is a response, tighten the joints or replace the tubing with new black PTFE tubing. We 
often find light leaks are caused by o-rings being left out of the assembly. 

8.11  Prom Replacement Procedure 

Preparation: If any setup changes such as RANGE, AUTOCAL, IZS ON/OFF etc. have been 
made, record the changes because all settings should be checked after the PROM is changed. See 
Figure 9-2 for location of prom on CPU card. 

1.

 

Turn the machine off. 

2.

 

Remove the hold down screw that holds in the V/F-CPU assembly to the motherboard. 

Disconnect the J9 power connector from the motherboard. Gently lift the assembly far 
enough out of the instrument to remove the connector to the display and the RS-232 
connector. 

3.

 

The CPU board is attached to the larger V/F board. 

4.

 

Remove the board, laying it down on an insulating surface such that the board edge pins 

on the PCB are on the left. The PROM chip should be at the top center. The current chip 
should be labeled with something like "210H9 - - -". See Figure 9-2 for prom location. 
Gently pry the chip from its socket and replace it with the new chip. Install the chip in the 
left end of the socket with the notch facing to the right. Make sure that all of the legs insert 
into the socket correctly. 

5.

 

Re-attach the CPU board to the V/F board, and re-attach the assembly to the 

motherboard. 

6.

 

Turn the M200A ON and observe the front panel display. As the machine goes through 

the setup the version number will be displayed on the front panel. It should read the same as 
the version number printed on the prom. 

7.

 

Re-enter any non-default settings such as RANGE or AUTOCAL. Re-enter the SPAN 

values in the CAL-CONC menu. Check all settings to make sure that expected setup 
parameters are present. 

8.

 

Re-calibrate the Analyzer so that the default slope and intercept are overwritten with the 

correct values. 

 

8-16 

Summary of Contents for 200A





























































































































































































































Reviews:

No comments