manualshive.com logo in svg

Teledyne 200A, Instruction Manual, Page: 200 / 220

Share
Download
Teledyne 200A Instruction Manual Download Page 200

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

1.

 

In SAMPLE mode, scroll the TEST functions to SAMP FLW. Observe the reading. Then 

subtract the observed reading from the desired reading. 

2.

 

Go to the VARS menu by SETUP-MORE-VARS, then pressing ENTR. Scroll to 

SFLOW_SET and press EDIT. The first value displayed is the SFLOW_SET:VALUE 
reading, ADD the value from step 1 to the reading shown and key in the new reading, then 
press ENTR. Check the low and high warning limits which are displayed as the next 2 values 
to make sure the new value does not exceed the warning limits. Press exit to return to 
SAMPLE mode.  

3.

 

Observe the SAMP FLW value. If necessary repeat step 2 to adjust the reading again to 

match the desired flow rate. 

9-58 

Summary of Contents for 200A





























































































































































































































Reviews:

No comments