Preparation for Use
3–10
MTD200 MPEG Test Decoder User Manual
Function Test (Power-on Test)
The unit is powered on by pressing the POWER switch (see Power in Table 3–1
on page 3–2). The MPEG test decoder then performs a built-in test which is
completed after a few seconds. When the boot phase is started, all LEDs on the
front panel light up and a memory test is carried out. If a memory error occurs,
all LEDs will be blinking. If there is no error, the LEDs are switched off and the
boot phase is continued.
The individual steps of the boot phase are indicated by LEDs. The SYNC LED
corresponds to the least significant bit, the PAT LED to the next higher bit, etc. If
an error occurs during the boot phase, the current status indicated by the LED
will be retained (see Table 3–3). Otherwise, the instrument is set to the previous-
ly used instrument status and the status menu is displayed.
Table 3–3: LED-Codes during booting of equipment
LED-Code
boot phase
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
0x01
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Check Update
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
0x02
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Loading of main program
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
0x03
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Starting of main program
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
0x32
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Reset of MPEG-2-Chipset
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
0x35, 0x36, 0x37
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Setting-up loading of MPEG-2-Demultiplexer
ÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁ
0x38
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Loading of MPEG-2-Audio Decoder
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
0x39
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Loading of MPEG-2-Video Decoder
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
0x3A
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Loading of Video-DAC
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
0x3B
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Starting of MPEG-2-Demultiplexer and MPEG-2-Video Decoder
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
0x3C
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Setting-up of ON Screen Display function
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
0x3D
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Loading of FPGA for protocol analysis
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
0x3F
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Loading of DSP for protocol analysis
The green LEDs next to the front-panel inputs indicate at which input the
instrument expects a signal. See Error Indication in Table 3–1 on page 3–3. If a
valid MPEG-2 signal is applied to the respective input, the instrument must
synchronize to it. When synchronization is completed, the lower (below TS)
green LED lights.
Summary of Contents for MTD200
