TAEHA PRO CAN PUMP DUAL User Manual Download Page 43

Page: 43 / 95

PRO CAN PUMP DUAL (PRO-CPD20)

Rev 1.6

2023/07/31

43/95

HMI Screen

7.1

Home page

The items are displayed in Home page, is just showed with current status, and the description is as below.

List

Description

Displays the PRO-CPD20 operating status.

: Normal operation

: Operation error alarm or perliminary alarm

: Occurs when control operation is no longer possible

RESIN

AUTO

Displays the configured resin mode on the left.

➔

Auto mode

HARDNER

MANUAL

Displays the configured hardner mode on the right.

➔

Manual mode

Displays the assembly status of the pail.

➔

Left : Pail not replaced.

➔

Right : Pail replacement complete

Displays run/stop status of the pump during equipment operation.

➔

Left : Pump run

➔

Right : Pump stop

Summary of Contents for PRO CAN PUMP DUAL





















































































Search results

Summary of Contents for PRO CAN PUMP DUAL

Reviews:

Related manuals for PRO CAN PUMP DUAL

Brands by name

Popular brands

TAEHA PRO CAN PUMP DUAL, User Manual

Search results

Summary of Contents for PRO CAN PUMP DUAL

Reviews:

Related manuals for PRO CAN PUMP DUAL

Brands by name

Popular brands