TAEHA PRO CAN PUMP DUAL User Manual Download

Page: 68 / 95

PRO CAN PUMP DUAL (PRO-CPD20)

Rev 1.6

2023/07/31

68/95

7.16

Alarm page

This page shows the alarm when there is a problem with using PRO-CPD20. The alarm description and
action for each item are as follows.

타워

알람

내용

원인

1. Emergency

The emergency stop button has

been pressed.

2. Main Air Press

Alarm for main pressure reaching

lower limit.

When status is

detected for about four
consecutive seconds.

3. RX-AI-INT

Error regarding monitoring

operation within the board.

4. RX-AI-EXT

Error regarding monitoring

operation within the board.

5. High Pressure

When the measurement value is

higher than the setting value of over
pressure.

When status is

detected for about 400
ms

6. Low Pressure

When feeding operation is run, if

measured value is kept below 80% of
the configured pressure value

When status is

detected for about five
consecutive seconds

Summary of Contents for PRO CAN PUMP DUAL





















































































Search results

Summary of Contents for PRO CAN PUMP DUAL

Reviews:

Related manuals for PRO CAN PUMP DUAL

Brands by name

Popular brands

TAEHA PRO CAN PUMP DUAL, User Manual

Search results

Summary of Contents for PRO CAN PUMP DUAL

Reviews:

Related manuals for PRO CAN PUMP DUAL

Brands by name

Popular brands