manualshive.com logo in svg

Tadiran Telecom TGW4 SERIES, User Configuration Manual

Share
Download
Tadiran Telecom TGW4 SERIES User Configuration Manual Download Page 115

TGW4/8 Gateway Series for Aeonix                                                                              High Availability Configuration Guide 

Tadiran Telecom (TTL) L.P.                                                                                                                                                           

103

 

4.2 Aeonix Configuration 

1.

 

Open the Aeonix Web Admin and login. 

2.

 

Perform 

License Requirements

 on page 

86

. Ensure that you have the correct licenses. 

3.

 

Perform 

FXS  Phone  Line  –  Basic  Configuration

  on  page 

87

. Define  all  TGW’s  FXS  stations  in 

Aeonix. 

4.

 

Perform 

FXO Trunk Line – Basic Configuration (TGW8-2G)

 on page 

90

. Define all TGW’s FXO 

trunks in Aeonix. FXO trunks must be assigned to trunk groups. 

4.3 Verification 

1.

 

Perform 

Call Status Verification

 on page 

71

. 

 

 

Summary of Contents for TGW4 SERIES















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands