manualshive.com logo in svg

Tadiran Telecom TGW4 SERIES, User Configuration Manual

Share
Download
Tadiran Telecom TGW4 SERIES User Configuration Manual Download Page 61

TGW4/8 Gateway Series for Aeonix                                                                                                      User Configuration Manual                                                                             

 

Tadiran Telecom (TTL) L.P.                                                                                                                                                                49

 

2.6.4 IP Table 

The IP filtering function is used to ignore the VoIP messages from untrusted networks.   

After login, click the 

Routing > IP Table

 tab to open the IP table configuration interface. 

Figure 2-25 

  IP Table Configuration Interface 

 

 

 

Add the authorized IP addresses to this table, and the gateways will only process the VoIP signaling from 

authorized IP addresses. If the IP table is empty, the gateways will not perform IP address-based message 

filtering. 

 

 

If the gateway is deployed in a public network, you are advised to set IP filtering to prevent call theft. 

 

 

 

 

Summary of Contents for TGW4 SERIES















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands