manualshive.com logo in svg

Tadiran Telecom TGW4 SERIES, User Configuration Manual

Share
Download
Tadiran Telecom TGW4 SERIES User Configuration Manual Download Page 125

TGW4/8 Gateway Series for Aeonix                                                                              High Availability Configuration Guide 

Tadiran Telecom (TTL) L.P.                                                                                                                                                           

113

 

5.2.2 Messages 

 

LLDP Message

 

Upon receipt of an LLDP message, the TGW will check if the VLAN ID, Priority, and DSCP fields are 

included. 

 

Figure 5-17 shows the LLDP message.

 

Figure 5-17 

LLDP Message 

 

 

 

Sent Message with a VLAN ID 

After obtaining a VLAN ID from the LLDP message, the TGW adds the VLAN information to the 

Ethernet frame headers of all messages to be sent. In addition, the TGW adds a DSCP value to the RTP 

message. 

 

Figure 5-18 shows the sent message with a VLAN ID. 

Figure 5-18 

Adding a VLAN ID to the message to be sent 

 

 

Summary of Contents for TGW4 SERIES















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands