Tadiran Telecom TGW4 SERIES User Configuration Manual Download Page 28 | Manualshive

Page: 28 / 142

Tadiran Telecom TGW4 SERIES User Configuration Manual Download Page 28

User Configuration Manual TGW4/8 Gateway Series for Aeonix

16 Tadiran Telecom (TTL) L.P.

Name

Description

Voice VLAN

VLAN to which the voice service (SIP signaling and RTP/T.38 media stream)
belongs.



None

: disable the voice VLAN



Mode 1

: SIP and RTP/T.38 are on the same VLAN



Mode 2

: SIP and RTP/T.38 are on different VLANs

Management
VLAN

Selected: enable the management VLAN
Deselected: disable the management VLAN

VLAN tag

Tag of the VLAN. The range is 1-4094.

VLAN QoS

Priority of the VLAN. The range is 0-7.

A larger value indicates a higher priority of a to-be-sent data packet.

IP address
assignment

Type for obtaining the IP address of the VLAN interface.



Static

: set the IP address to a static IP address



DHCP

: automatically obtain an IP address by using the DHCP protocol

IP address

IP address of the VLAN interface

Netmask

Subnet mask of the VLAN interface

Gateway IP
address

IP address of the gateway of the VLAN interface

MTU

Maximum Transmission Unit value of the VLAN interface.
The range is 576-1500. The default value is 1500.



A reboot is required to enable the VLAN configuration.



After a VLAN is configured, only PCs in the same VLAN can access the TGW.



The TGW address used to log in to the Web GUI can be obtained by connecting a phone to an
FXS (Phone) port of the TGW, and dialing "##". In the case of a single VLAN, the IP address of
the single VLAN is voiced; in the case of a multi-service VLAN, the IP address of the
management VLAN is voiced.

«
...
26
27
28
29
30
...
»

Summary of Contents for TGW4 SERIES















































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands