manualshive.com logo in svg

Tadiran Telecom TGW4 SERIES, User Configuration Manual

Share
Download
Tadiran Telecom TGW4 SERIES User Configuration Manual Download Page 62

User Configuration Manual                                                                                                      TGW4/8 Gateway Series for Aeonix 

 

50                                                                                                                                                                Tadiran Telecom (TTL) L.P. 

2.7 Advanced Configuration 

2.7.1 System 

After login, click the 

Advanced > System

 tab to open this interface. 

Figure 2-26 

Interface of System Advancsed Configuration   

 

 

 

Table 2-21 

NAT Configuration Parameters 

Note: * indicates mandatory parameters for Aeonix US ALARMS. 

Name 

Description 

NAT 

 

* 
NAT traversal 

Gateways support several mechanisms for NAT traversal. Usually, static NAT is used 
when a fixed public IP address is available. It is necessary to perform port mapping or 
DMZ function on router when selecting dynamic or static NAT. 
For Aeonix US ALARMS 

 Select 

Off

 

Summary of Contents for TGW4 SERIES















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands