Tadiran Telecom TGW4 SERIES User Configuration Manual Download Page 140

Page: 140 / 142

High Availability Configuration Guide TGW4/8 Gateway Series for Aeonix

128

Tadiran Telecom (TTL) L.P

Configuring the Domain Name of the Primary Server

In case the primary SIP server is located through the domain name (

Basic > SIP

tab,

Step3 on page

126), do the following:

Step1

Click the

Basic > Network

tab.

Figure 6-31

Page to set DNS server

Step2

Make sure DNS server can be obtained automatically or has been specified manually.

Step3

Enter the IP address in

Primary DNS server

field.

Step4

You can also fill in a backup IP address in

Standby SIP proxy server 1

See Step1 and

‎Step2

on page 127. This allows the device to failover to the backup IP address if

the domain name resolution service fails.

Step5

Click

Save

Summary of Contents for TGW4 SERIES















































































































































Search results

Summary of Contents for TGW4 SERIES

Reviews:

Brands by name

Popular brands

Tadiran Telecom TGW4 SERIES, User Configuration Manual

Search results

Summary of Contents for TGW4 SERIES

Reviews:

Brands by name

Popular brands