manualshive.com logo in svg

Tadiran Telecom TGW4 SERIES, User Configuration Manual

Share
Download
Tadiran Telecom TGW4 SERIES User Configuration Manual Download Page 132

High Availability Configuration Guide                                                                                      TGW4/8 Gateway Series for Aeonix                                                                               

120

                                                                                                                                                            Tadiran Telecom (TTL) L.P   

6.3.2 Set Standby SIP Servers 

Step0   

If a domain name was entered in the 

Registrar server

 field, 

 

Step3 above,   

skip to 

Configuring the Domain Name of the Primary Server

, on next page. 

Configuring the IP Address of Standby SIP Servers 

A maximum of five servers can be added 

To configure the IP addresses of the standby SIP servers: 

Step1   

Click 

Add

. 

Step2   

In the 

Standby SIP proxy server n

 field enter the IP address of the standby SIP server. 

Step3   

Repeat  Step1 and  Step2 for the next standby server, up to five standby servers. 

Step4   

Click 

Save

. 

Step5   

Skip to 

Set the Failover Condition

, on page 122. 

 

Figure 6-23 

Page to set standby servers 

 

 

For detailed information, see

 

 2.3.6 

High Availability Configuration

 on page 

21

. 

Summary of Contents for TGW4 SERIES















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands