manualshive.com logo in svg

Tadiran Telecom TGW4 SERIES, User Configuration Manual

Share
Download
Tadiran Telecom TGW4 SERIES User Configuration Manual Download Page 103

TGW4/8 Gateway Series for Aeonix                                                                                  High Availability Configuration Guide 

Tadiran Telecom (TTL) L.P.

   

                                                                                                                                                       

91

 

4 

Appendix: Quick Configuration Procedure   

This chapter describes the minimal settings instructions needed to use the TGW4/8 series gateways 
with Aeonix.

 

4.1 Gateway Unit Configuration 

4.1.1 Basic Configuration 

1.

 

Connect the TGW unit to the network via port WAN. 

2.

 

Open the TGW Web Admin and login, as described in section 

 

2.1.2 

Logging In

, on page 

10. 

3.

 

Click the 

Basic > Network

 tab.

 

  For detailed information, see

 

Network Configuration

 on page 

13

. 

a)

 

Select the 

Obtain DNS server address automatically

 check box. 

b)

 

From the 

Setup

 drop-down list,

 

select 

Static IP

.

 

 

Summary of Contents for TGW4 SERIES















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands