manualshive.com logo in svg

Tadiran Telecom TGW4 SERIES, User Configuration Manual

Share
Download
Tadiran Telecom TGW4 SERIES User Configuration Manual Download Page 96

User Configuration Manual                                                                                                      TGW4/8 Gateway Series for Aeonix 

 

84                                                                                                                                                                Tadiran Telecom (TTL) L.P. 

2.10.5 Capture Recordings on the Port 

After login, click the 

Tools > TDM

 

capture

 tab to open this interface. This tool can be used to capture 

the voice stream from the Phone or Line interface. When the call lasts longer than 200 sec, only the first 

200 sec of voice stream will be captured. The voice file is stored on the gateway in PCMU format. 

Figure 2-55 

Interface for capturing Port Recordings 

 

 

 

2.10.6 Ethereal Capture 

After login, click the 

Tools > Ethereal

 

capture

 tab to open this interface. You are allowed to capture up 

to three IP voice data files, each with up to 2M bytes. The data files are stored on the gateway in 

dump.cap format under catalog /var/log. 

Figure 2-56 

Ethereal Capture Interface 

 

 

 

 

 

Summary of Contents for TGW4 SERIES















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands