manualshive.com logo in svg

Tadiran Telecom TGW4 SERIES, User Configuration Manual

Share
Download
Tadiran Telecom TGW4 SERIES User Configuration Manual Download Page 138

TGW4/8 Gateway Series for Aeonix                                                                                                      User Configuration Manual                                                                             

 

Tadiran Telecom (TTL) L.P.

   

                                                                                                                                                       

126

 

6.4 Configuring Load Balancing Mode (must for Aeonix) 

6.4.1 Enable Load Balancing Feature 

To configure the 

Load balancing 

mode: 

Step1   

Click the 

Basic > SIP

 tab. 

 

Figure 6-29 

Load balancing configuration page 

 

For detailed information, see

 

 2.3.6 

High Availability Configuration

 on page 

21

. 

 

Step2   

From the 

High availability

 - 

Mode

 drop-down list, select 

Load balancing

.

 

Step3   

In the 

Registrar serve

r field, enter the primary Aeonix server IP address or domain name.

 

Step4   

Click 

Save

. 

 

 

Summary of Contents for TGW4 SERIES















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands