manualshive.com logo in svg

Tadiran Telecom TGW4 SERIES, User Configuration Manual

Share
Download
Tadiran Telecom TGW4 SERIES User Configuration Manual Download Page 141

TGW4/8 Gateway Series for Aeonix                                                                              High Availability Configuration Guide 

Tadiran Telecom (TTL) L.P.

     

                                                                                                                                                     

129

 

6.4.3 Configure OPTIONS and REGISTER Settings 

In the load balancing mode, the following timers must be configured: 

Step1  

In the 

OPTIONS request period 

field,

 

enter

 

the interval between receiving the response (200) from the SIP 

server to the previous OPTIONS and sending the next OPTIONS. 

Step2  

In the 

OPTIONS request timeout 

field,

 

enter the period since the sending of the last OPTIONS with no 

response by the SIP server. 

Step3  

In the 

REGISTER request timeout

 field,

 

enter the period from the sending of the first REGISTER with no 

response by the previous SIP server to the sending of REGISTER to the next SIP server. 

 

Figure 6-32 

Page to configure OPTIONS and REGISTER settings 

 

 

 

   

 

 

 

Summary of Contents for TGW4 SERIES















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands