manualshive.com logo in svg

Tadiran Telecom TGW4 SERIES, User Configuration Manual

Share
Download
Tadiran Telecom TGW4 SERIES User Configuration Manual Download Page 98

TGW4/8 Gateway Series for Aeonix                                                                                                      User Configuration Manual                                                                             

 

Tadiran Telecom (TTL)_L.P.                                                                                                                                                            86 

 

3 

Aeonix Configuration 

It is necessary to define all FXS stations and FXO trunks in Aeonix, before any calls can be routed 
through them. Trunks must be assigned to trunk groups to operate in the Aeonix system. 

 

For detailed information, refer to the 

Aeonix Administration Manual

. 

Chapter 3, Getting Started > Licenses 
Chapter 6, Managing Users 
Chapter 7, Managing Phones 
Chapter 8, Managing Trunk Groups

 

Chapter 9, Managing Trunks 

3.1 License Requirements 

Verify that you have the correct licenses.   

 

FXS stations require the "

Aeonix Gateway users

" license 

 

FXO trunks require the "

Aeonix SIP Trunks & Gateways (concurrent calls)

" license 

 

1.

 

Open the Aeonix Web Admin. 

2.

 

At the bottom of the navigation pane, click 

System

. The pane displays the System menus. 

3.

 

Select the 

License 

menu, and then click 

License

. 

Figure 3-1 

Aeonix License Information Page

 

 

 

Summary of Contents for TGW4 SERIES















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands