Sony DVCAM DSR-60, Service Manual

Page: 20 / 324

1-10
DSR-80/80P/60/60P
Features
Chapter 1 Overview
18
Chapter 1 Overview
CH-1
AUDIO IN 600
Ω
OFF ON
0dBm
-8dBm +4dBm
CH-2
600
Ω
0dBm
-8dBm +4dBm
CH-3
600
Ω
0dBm
-8dBm +4dBm
CH-4
600
Ω
0dBm
-8dBm +4dBm
AUDIO OUT
CH-1 CH-2 CH-3 CH-4
OFF ON OFF ON OFF ON
ANALOG I/O
REF.VIDEO
IN
75
Ω
ON
OFF
OUT
IN
OUT
TIME CODE
VIDEO IN
75
Ω
ON
OFF
Y-R,B
RGB
Y-R,B
RGB
VIDEO OUT
1
2
(SUPER)
Y IN
G
R-Y
R
B-Y
B
Y
G
R-Y
R
B-Y
B
MONITOR
AUDIO
OUT IN
S VIDEO
COMPONENT VIDEO R.G.B.
OUT
4
Analog audio signal input/output section
Location and Function of Parts
1
AUDIO IN 600
Ω
ON/OFF switches
Use these switches to select either 600
Ω
impedance
(the ON setting) or 10-k
Ω
impedance (the OFF setting)
for the AUDIO IN CH-1 to CH-4 connectors.
2
AUDIO IN –6 dBm/0 dBm/+4 dBm switches
Set these switches according to the levels of the signals
input to the AUDIO IN CH-1 to CH-4 connectors.
3
AUDIO IN CH-1 (channel 1) to CH-4 connectors
(XLR 3-pin, female)
Use these connectors to connect separate channels of
audio input from a player VCR or other external audio
equipment.
4
AUDIO OUT CH-1 (channel 1) to CH-4
connectors (XLR 3-pin, male)
Output channel-1 to channel-4 audio signals,
respectively.
5
MONITOR AUDIO connector (RCA phono
jack)
Outputs audio signals for monitoring. The audio
signals to be output from this connector can be
selected with the MONITOR SELECT switches on the
menu control panel
4
(see page 13).
1
AUDIO IN 600
Ω
ON/OFF switches
2
AUDIO IN –6 dBm/0 dBm/+4 dBm
switches
3 AUDIO IN CH-1 to CH-4 connectors
4
AUDIO OUT CH-1 to CH-4
connectors
5
MONITOR AUDIO connector
Chapter 2 Recording and Playback
Chapter 2 Recording and Playback
19
Recording
This section describes the necessary settings and operations to perform
recording on this unit. The same settings and operations apply whether
you are using the unit as part of an editing system, for dubbing
1) , or as a
stand-alone recorder. For the necessary connections for recording and the
settings not covered in this section, see Chapter 5 “Connections and
Settings”.
Settings for Recording
Note
When controlling this unit from an editing controller, set the REMOTE/
LOCAL switch to “REMOTE”. When not, set the switch to “LOCAL”.
1
Power on the video monitor, then set the monitor’s input switches
according to the input signals from this unit.
2
Set up the player to play back a tape.
For details, refer to your player’s operating instructions.
3
Power on this unit by pressing on the “
1
” side of the POWER switch.
Chapter 2 Recor
ding and Pla
ybac
k
) 0 6 r p
3
7 6 5 4
1 2
) 0 6 p
INPUT MODE display
AUDIO MODE display
Audio level meter
Video monitor Player (DSR-60/60P, etc.)
Recorder (DSR-80/80P)
REMOTE/LOCAL
switch
(Continued)
........................................................................................................................................................................................................
1) For dubbing of QSDI format signals, use the auto mode
(AUTO FUNCTION) execution menu item QSDI
DUBBING.
For details, see the section “Dubbing Signals in QSDI
Format” on page 38.