Sony DVCAM DSR-60, Service Manual

Page: 32 / 324

1-22
DSR-80/80P/60/60P
42
Chapter 4 Menu Settings
Chapter 4
Menu Settings
Menu Contents
SETUP Menu
The purpose and settings of the setup menu items are
described below.
Indications of menu Items and settings
• In the table below entitled “Menu Contents”, the
indication of each menu item or setting on the
monitor screen is shown first, then the indication of
the same item or setting on the time counter display
of this unit is shown in square brackets ([ ]).
(Examples)
• Settings that have an asterisk in front of them (such
as
∗
EE) are factory default settings.
• On the time counter display, one to three “>” symbols
may precede item or setting indications depending on
the current menu level. Larger numbers of “>”
symbols indicate lower menu levels.
Menu contents
OPERATIONAL FUNCTION [Operational]: Operation
settings
Description of settings
AUTO EE SELECT [> Auto
EE]: Determine whether
the unit enters EE mode or
PB mode when audio and
video signals from other
equipment are input.
When this unit is used as
the recorder for cut editing,
it is possible to output the
input audio and video
signals to the monitor. The
term “EE” mode is used to
refer to this feature, which
enables the entire editing
operation to be carried out
with a single monitor.
∗
EE [>>> EE]: Output video and audio signals from other
equipment.
PB [>>> PB]: Mute video and audio signals.
CASSETTE OUT [>> Cass.
out]: Operations when the
cassette has been ejected
F. FWD/REW a) [>> F. FWD/
REW]: Operations when in
fast forward or rewind
mode
EE [>>> EE]: Output video and audio signals from other
equipment.
∗
PB [>>> PB]: Mute video and audio signals. (However,
holding down the F FWD or REW button on the front panel
makes this setting ineffective temporarily and allows you to
perform a picture search at 32 times normal speed in
forward or reverse direction.)
STOP [>> STOP]:
Operations when in stop
mode
EE [>>> EE]: Output video and audio signals from other
equipment.
∗
PB [>>> PB]: The unit enters playback mode and outputs a
still picture.
STANDBY OFF [>> STBY
OFF]: Operations when in
standby off mode
EE [>>> EE]: Output video and audio signals from other
equipment
∗
PB [>>> PB]: The unit enters playback mode and outputs a
still picture.
LOCAL ENABLE [> Local ENA]: Select which of the tape
transport control buttons (EJECT, REW, PLAY, F FWD,
STOP, REC) operate when the REMOTE/LOCAL switch is
set to REMOTE.
ALL DISABLE [>> All DIS]: All of the tape transport control
buttons are disabled.
∗
STOP & EJECT [>> STOP & E]: Only the STOP and EJECT
buttons are enabled.
ALL ENABLE [>> All ENA]: All of the tape transport control
buttons are enabled, and settings such as preroll time
change or time data display selection are effective.
MAX SRCH SPEED [> Max SRCH]: Set the maximum value
for search mode.
×
16 [>>
×
16]: Restrict the search speed to the maximum 16
times normal for which the picture can be seen on the
monitor. Use this setting when using search mode for
cueing.
∗×
32 [>>
×
32]: Restrict the search speed to the maximum
32 times normal for which the picture can be seen on the
monitor. Use this setting when using search mode for
cueing.
×
85 [>>
×
85]: Allow searching at up to the maximum tape
transport speed of 85 times normal. The picture cannot be
seen on the monitor at this speed.
AUTO REW [> AUTO REW]: Determine whether or not to
rewind automatically when playback reaches the end of a
tape.
∗
ENABLE [>> ENABLE]: Rewind automatically.
DISABLE [>> DISABLE]: Do not rewind automatically.
a) Note
Set this item to “PB” when you want to use the F FWD
and REW buttons to view playback at 32 times normal
speed. If this item is set to “EE”, holding down the F
FWD and REW buttons produces EE pictures.
∗
EE
Indication in monitor
screen Indication in time
counter display
OPERATIONAL FUNCTION [Operational]
CASSETTE OUT [>> Cass. out]
[>>> EE]
(Continued)
Chapter 4 Menu Settings
43
Chapter 4
Menu Settings
Menu contents (Continued)
OPERATIONAL FUNCTION [Operational]: Operation
settings
Description of settings
PREROLL TIME [> Preroll]: Set the preroll time. The preroll time can be set in one-second increments to
between 0 and 15 seconds (0 SEC [>> 0 SEC] to 15 SEC
[>> 15 SEC]). When an editing controller such as the PVE-
500 has been connected, this setting is disabled and the
editing controller’s setting is in effect. Operations such as the
preroll time setting and the time data switching operation are
also performed on the editing controller.
Factory default setting: 5 SEC [>> 5 sec]
AFTER CUE-UP [> After CUE]: Select the operating mode
following cue-up.
∗
STOP [>> STOP]: Stop mode
STILL [>> STILL]: Output still pictures in search mode.
PLAY START [> PLAY start]: Set the timing for switching
from stop mode to playback mode.
In an editing system including an editing controller such as
the PVE-500, adjusting this setting so that the delay before
switching to playback mode is the same on all the decks of
the editing system means that there is no longer a need to
synchronize the decks for editing, and the preroll time can
be shortened.
16 FRAME DELAY [>> 16 delay] to 4 FRAME DELAY
[>> 4 delay]: The larger the numerical value, the longer the
delay. By adjusting this setting, it is possible to reduce the
phase synchronization time and preroll time during editing.
Factory default setting: 5 FRAME DELAY [>> 5 delay] (for
DSR-80) or 4 FRAME DELAY [>> 4 delay] (for DSR-80P)
A1 EDIT CH [> A1 Edit CH]: Determine which audio channel
the EDIT PRESET command set on an editing controller
(such as the PVE-500) for A1 is assigned to.
∗
CH-1 [>> CH-1]: Assign to channel 1.
CH-2 [>> CH-2]: Assign to channel 2.
CH-3 [>> CH-3]: Assign to channel 3.
CH-1 & CH-2 [>> CH-1&2]: Assign to channel 1 and channel
2.
A2 EDIT CH [> A2 Edit CH]: Determine which audio channel
the EDIT PRESET command set on an editing controller
(such as the PVE-500) for A2 is assigned to.
∗
CH-2 [>> CH-2]: Assign to channel 2.
CH-3 [>> CH-3]: Assign to channel 3.
CH-4 [>> CH-4]: Assign to channel 4.
CH-3 & CH-4 [>> CH-3&4]: Assign to channel 3 and channel
4.
A MODE CHANGE [> Aud change]: Determine whether or
not to permit an insert editing that uses a different audio
recording mode (2- or 4-channel mode) from that which
was used for the tape loaded in the recorder.
∗
OFF [>> OFF]: Do not permit.
ON [>> ON]: Permit.
QSDI AUDIO MON [> QSDI A mon]: Determine what type of
audio signal to be output as EE audio when the selected
input is QSDI.
∗
QSDI [>> QSDI]: Output the input QSDI audio as it is.
ANALOG [>> Analog]: Automatically switch audio input
selection and output analog audio.
AES/EBU [>> AES/EBU]: Automatically switch audio input
selection and output AES/EBU format digital audio.
SDI [>> SDI]: Automatically switch audio input selection and
output SDI format digital audio.
DISPLAY CONTROL [Display]: Settings related to
indications on the monitor and the unit Description of settings
CHARA. DISPLAY [> Chara disp]: Determine whether or not
to output text (such as time code numbers) from the VIDEO
OUT 2 (SUPER) connector.
∗
ON [>> ON]: Output text.
OFF [>> OFF]: Do not output text. (In spite of this setting,
pressing the MENU button causes menu text to be output.)
CHARA. POSITION [> Chara pos]: Set the position of text
superimposed on output from the VIDEO OUT 2 (SUPER)
connector to the monitor.
Use ¿ ÷ ˘ ≥ buttons on the menu control panel to adjust
the indication position while watching the monitor screen.
Press the MENU button to confirm the setting and return to
the level 1 of the setup menu.
(Continued)