1-5
26
— Recording – Basics —
Recording a picture
Your camcorder automatically focuses for you.
(
1
)
Remove the lens cap by pressing both knobs
on its sides and attach the lens cap to the grip
strap.
(
2
)
Install the power source and insert a cassette.
See “Step 1” to “Step 3” for more information
(p. 17 to p. 25).
(
3
)
Set the POWER switch to CAMERA while
pressing the small green button. Your
camcorder is set to the standby mode.
(
4
)
Press OPEN to open the LCD panel. The
viewfinder automatically turns off.
(
5
)
Press START/STOP. Your camcorder starts
recording. The REC indicator appears. The
camera recording lamp located on the front of
your camcorder lights up. To stop recording,
press START/STOP again.
Note
Fasten the grip strap firmly.
— Запись – Основные положения —
Запись изображения
Ваша видеокамера автоматически выполняет
фокусировку для Вас.
(
1
)
Снимите крышку объектива, нажав на обе
кнопки на ее сторонах, и закрепите
крышку объектива на ремне для захвата.
(
2
)
Установите источник питания и
установите кассету. Подробные сведения
приведены в “Пункте 1” - “Пункте 3” (стр.
17 - 25).
(
3
)
Удерживая нажатой маленькую зеленую
кнопку, установите переключатель
POWER в положение CAMERA. Ваша
видеокамера переключится в режим
ожидания.
(
4
)
Нажав кнопку OPEN, откройте панель
ЖКД. Видоискатель автоматически
выключится.
(
5
)
Нажмите кнопку START/STOP. Ваша
видеокамера начнет запись. Появится
индикатор REC. Высветится лампочка
записи, расположенная на передней
панели видеокамеры. Для остановки
записи нажмите кнопку START/STOP еще
раз.
Примечание
Плотно пристегните ремень для захвата.
0:00:01
40min
REC
VCR
CAMERA
MEMORY
OFF(CHG)
POWER
1
3
5
2
4
LOCK switch/
Переключатель
LOCK
Microphone/
Микрофон
Camera recording lamp/
Лампочка записи
видеокамеры
27
Recording
–
Basics
Запись – Основные положения
Recording a picture
Note on Recording mode
Your camcorder records and plays back in the SP
(standard play) mode and in the LP (long play)
mode. Select SP or LP in the menu settings. In the
LP mode, you can record 1.5 times as long as in
the SP mode.
When you record a tape in the LP mode on your
camcorder, we recommend playing the tape on
your camcorder.
Note on the LOCK switch
When you slide the LOCK switch to the right, the
POWER switch can no longer be set to MEMORY
accidentally. LOCK switch is set to the left as a
default setting.
To enable smooth transition
Transition between the last scene you recorded
and the next scene is smooth as long as you do
not eject the cassette even if you turn off your
camcorder.
However, check the following:
– Do not mix recordings in the SP mode and ones
in the LP mode on one tape.
– When you change the battery pack, set the
POWER switch to OFF (CHG).
– When you use a tape with cassette memory,
however, you can make the transition smooth
even after ejecting the cassette if you use the
END SEARCH function (p. 37).
If you leave your camcorder in the standby
mode for 5 minutes while the cassette is
inserted
Your camcorder automatically turns off. This is
to save battery power and to prevent battery and
tape wear. To resume the standby mode, set the
POWER switch to OFF (CHG), and to CAMERA
again.
When you record in the SP and LP modes on
one tape or you record some scenes in the LP
mode
The playback picture may be distorted or the
time code may not be written properly between
scenes.
Recording data
The recording data (date/time or various settings
when recorded) are not displayed while
recording. However, they are recorded
automatically onto the tape. To display the
recording date and time, press DATA CODE
during playback.
Запись изображения
Примечание по режиму записи
Ваша видеокамера выполняет запись и
воспроизведение в режиме SP (стандартное
воспроизведение) и в режиме LP
(долгоиграющее воспроизведение). Выберите
команду SP или LP в установках меню. В
режиме LP Вы можете выполнять запись в 1,5
раза дольше по времени, чем в режиме SP.
При выполнении на Вашей видеокамере
записи на ленту в режиме LP рекомендуется
воспроизводить эту ленту также на Вашей
видеокамере.
Примечание по переключателю LOCK
Если Вы передвинете переключатель LOCK
вправо, то переключатель POWER уже не
может быть случайно установлен в
положение MEMORY. Переключатель LOCK
находится в левом положении по умолчанию.
Для обеспечения плавного перехода
Вы можете выполнять плавный переход
между последним записанным эпизодом и
следующим эпизодом до тех пор, пока не
извлечете кассету, даже при выключении
Вашей видеокамеры.
Тем не менее, проверьте следующее:
– Не чередуйте записи в режимах LP и SP на
одной ленте.
– При замене батарейного блока установите
переключатель POWER в положение OFF
(CHG).
– При использовании ленты с кассетной
памятью, Вы, тем не менее, можете
выполнить плавный переход даже после
извлечения кассеты, если Вы используете
функцию END SEARCH (стр. 37).
Если Вы оставите Вашу видеокамеру в
режиме ожидания на 5 минут при
вставленной кассете
Видеокамера выключится автоматически.
Это предотвращает расход заряда
батарейного блока и износ ленты. Для
возобновления режима ожидания установите
сначала переключатель POWER в положение
OFF (CHG), а затем снова верните его в
положение CAMERA.
Если Вы записываете в режимах SP и LP
на одной и той же кассете, или Вы
записываете некоторые эпизоды в режиме
LP
При воспроизведении изображение может
быть искажено или код времени может не
записаться правильно между эпизодами.
Дата записи
Данные записи (дата/время или различные
установки при записи) не отображаются во
время записи. Тем не менее, они
автоматически записываются на ленту.
Чтобы отобразить дату и время записи,
нажмите кнопку DATA CODE во время
воспроизведения.
28
Recording a picture
Adjusting the LCD screen
The LCD panel moves about 90 degrees to the
viewfinder side and about 180 degrees to the lens
side.
If you turn the LCD panel over so that it faces the
other way, the
indicator appears on the LCD
screen and in the viewfinder
(Mirror mode)
.
When closing the LCD panel, set it vertically, and
swing it into the camcorder body.
Adjusting the brightness of the
LCD screen
To adjust the brightness of the LCD screen, press
either of the two buttons on LCD BRIGHT.
180
°
90
°
After recording
(
1
)
Set the POWER switch to OFF (CHG).
(
2
)
Close the LCD panel.
(
3
)
Eject the cassette.
Запись изображения
Регулировка экрана ЖКД
Панель ЖКД может передвигаться примерно
на 90 градусов в сторону видоискателя и
примерно на 180 градусов в сторону
объектива.
Если Вы перевернете панель ЖКД так, что
она будет направлена в другую сторону, на
экране ЖКД и в видоискателе появится
индикатор
(зеркальный режим)
.
При закрывании панели ЖКД установите ее
вертикально, а затем поверните ее к корпусу
видеокамеры.
Регулировка яркости экрана
ЖКД
Для регулировки яркости экрана ЖКД
нажмите на любую из двух кнопок LCD
BRIGHT.
После записи
(
1
)
Установите переключатель POWER в
положение OFF (CHG).
(
2
)
Закройте панель ЖКД.
(
3
)
Извлеките кассету.
LCD
BRIGHT
to dim/
темнее
to brighten/
светлее
29
Recording
–
Basics
Запись – Основные положения
Recording a picture
Note
When using the LCD screen except in the mirror
mode, the viewfinder automatically turns off.
When you use the LCD screen outdoors in
direct sunlight
The LCD screen may be difficult to see. If this
happens, we recommend that you use the
viewfinder.
Picture in the mirror mode
The picture on the LCD screen is a mirror-image.
However, the picture will be normal when
recorded.
During recording in the mirror mode
ZERO SET MEMORY on the Remote
Commander does not work.
Indicators in the mirror mode
The STBY indicator appears as
Xz
and REC as
z
. Some of the other indicators appear mirror-
reversed and others are not displayed.
LCD screen backlight
You can adjust the brightness of the backlight.
Select LCD B.L. in the menu settings
(p. 131).
Even if you adjust the LCD screen backlight or
brightness of the LCD screen
The recorded picture will not be affected.
Запись изображения
Примечание
При использовании экрана ЖКД
видоискатель автоматически выключается,
кроме зеркального режима.
Если Вы используете экран ЖКД вне
помещения под прямым солнечным
светом
Возможно будет трудно разглядеть экран
ЖКД. Если это произойдет, рекомендуется
использовать видоискатель.
Изображение в зеркальном режиме
Изображение на экране ЖКД будет
отображаться зеркально. Несмотря на это,
запись изображения будет нормальной.
Во время записи в зеркальном режиме
Кнопка ZERO SET MEMORY на пульте
дистанционного управления не
функционирует.
Индикаторы в зеркальном режиме
Индикатор STBY появится в виде
Xz
, а
индикатор REC в виде
z
. Некоторые другие
индикаторы появятся в зеркально
отображенном виде, а некоторые из них не
будут отображаться совсем.
Задняя подсветка экрана ЖКД
Вы можете отрегулировать яркость задней
подсветки. Выберите пункт LCD B.L. в
установках меню (стр. 138).
Даже если Вы регулируете заднюю
подсветку экрана ЖКД или яркость
экрана ЖКД
На записанное изображение это не повлияет.