Simrad WBT Mini Instruction Manual Download Page 64

Page: 64 / 68

425197/B

Technical specifications

These performance specifications summarize the main functional and operational
characteristics of the WBT Mini.

All specifications are maximum ratings. We are continuously working to improve the
quality and performance of our products. The technical specifications may be changed
without prior notice.

Performance specifications

•

Frequency range

: 30–500 kHz

•

Pulse duration

: 64–2048 µs

•

Pulse forms

: CW + FM (Linear upsweep)

•

Transmit power

: 1000 W @ 55 Ω (Maximum)

•

Number of channels

: 4 (With multiplexer: 8)

•

Transducer options

: Single-beam/Split-beam

•

Memory capacity

(Autonomous mode): 512 GB

A high-quality USB flash drive is used.

Weight and outline dimensions

•

Outline dimensions

–

Depth

: 145 mm

–

Width

: 289 mm

–

Height

: 127 mm

•

Weight

: 5.4 kg

Power requirements

•

Voltage requirement

: 12–16 VDC

•

Power consumption

Simrad WBT Mini Instruction Manual

Summary of Contents for WBT Mini





































































Search results

Summary of Contents for WBT Mini

Reviews:

Related manuals for WBT Mini

Brands by name

Popular brands

Simrad WBT Mini, Instruction Manual

Search results

Summary of Contents for WBT Mini

Reviews:

Related manuals for WBT Mini

Brands by name

Popular brands