Simrad WBT Mini Instruction Manual Download Page 5

Page: 5 / 68

425197/B

Table of contents

ABOUT THIS MANUAL .................................................................. 5

SIMRAD WBT MINI...................................................................... 6

USING THE WBT MINI IN EK80 MODE ....................................... 12

About EK80 mode ................................................................................................................ 13
Defining the IP address on the PC network adapter for communication with the WBT

Mini .................................................................................................................................. 13

Obtaining and installing the software license ....................................................................... 14
Installing one or more transducers........................................................................................ 16
Installing transceiver channels.............................................................................................. 19
Disconnecting transceiver channels...................................................................................... 21

USING THE WBT MINI IN AUTONOMOUS MODE......................... 23

About Autonomous mode ..................................................................................................... 24
Switching between

Autonomous

mode and

EK80

mode ...................................................... 25

Installing the software driver for the serial interface cable................................................... 26
Removing the USB flash drive from the WBT Mini ............................................................ 27
Inserting the USB flash drive in the WBT Mini ................................................................... 29
Installing the software driver for the USB flash drive .......................................................... 31
Waking up the WBT Mini from

Sleep

state.......................................................................... 32

INSTALLATION .......................................................................... 34

Installing the WBT Mini....................................................................................................... 35
About the drawings in the drawing file................................................................................. 36
413455 WBT Mini dimensions............................................................................................. 37

CABLE LAYOUT AND INTERCONNECTIONS................................. 39

Cable plan ............................................................................................................................. 40
List of WBT Mini cables ...................................................................................................... 42
Connectors ............................................................................................................................ 43

Ethernet and DC power connector .............................................................................. 43
Transducer connectors................................................................................................. 45
Serial line connector .................................................................................................... 47

Instruction Manual

Summary of Contents for WBT Mini





































































Search results

Summary of Contents for WBT Mini

Reviews:

Related manuals for WBT Mini

Brands by name

Popular brands

Simrad WBT Mini, Instruction Manual

Search results

Summary of Contents for WBT Mini

Reviews:

Related manuals for WBT Mini

Brands by name

Popular brands