Simrad WBT Mini Instruction Manual Download Page 50 | Manualshive

Page: 50 / 68

background image

48

425197/B

This is the pin configuration for a female socket, as seen towards the socket (face view).

Serial line interface cables

A ready-made cable is available. The serial interface cable is manufactured by Kongsberg
Maritime using a commercial USB-to-serial converter. It is terminated with an 8-pin
MCIL8M subsea connector. The cable is approximately 2.5 metres long.

An extension cable is also available.

Related topics

Cable layout and interconnections, page 39
Serial line interface cable and connector (description), page 50
Extension cable (description), page 52
Serial line interface cable (Spare part), page 60
Extension cable (Spare part), page 61

Simrad WBT Mini Instruction Manual

«
...
48
49
50
51
52
...
»

Summary of Contents for WBT Mini





































































Reviews:

No comments

Related manuals for WBT Mini

Brand: Hammarlund Pages: 38

Brand: Hammarlund Pages: 22

Brand: Hammarlund Pages: 87

Brand: RadioLink Pages: 4

Brand: Radio Industries Pages: 26

HD-PLC DA-PU100

Brand: Panasonic Pages: 16

Brand: Sangean Pages: 1

65-2646XL-05-04

Brand: RKI Instruments Pages: 66

Brand: Advance Paris Pages: 2

Brand: Yaesu Pages: 20

Brand: Clas Ohlson Pages: 30

Brand: Sytech Pages: 6

Brand: ADI Pages: 47

Brand: nedis Pages: 84

Brand: Elvox Pages: 8

Brand: Tecsun Pages: 12

Brand: T&D Pages: 2

Brand: Peiying Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands