manualshive.com logo in svg

Siemens TXP-CLC, Manual

Share
Download
Siemens TXP-CLC Manual Download Page 50

 
 

 

 

 

TXP CLC Course

 

 

 

 

Identification of Mounting Location Example 

 
In Figure 3 an example of a KKS structure for identification of mounting location 
is shown. The prefix "+" is used to represent mounting location information. The 
"." between CJP02 and DC015 is used to identify that DC015 is a module 
location within the cabinet CJP02. This identifier is used in the I&C manuals. 
 

 
 
 
 
 
 
 

Identification of Mounting Location 

 

                  +    11   UBA01  CJP02 . DC015

 

 

Module location 
Tier = DC 
Slot = 015 

 

Cabinet Number 
TXP Cabinet 2 

 

Location 
Electrical Container 1 

 

Unit 11 

 

 
 

 

 

 

 

    Mounting Location Identifier  

 
 
 

Figure 3  -  Identification of Mounting Location 

 

Training Center 

Copying of this document, and giving it to others and use or communication of the contents, are forbidden without express authority. Offenders are liable to the payment of 
damages. All rights are reserved in the event of the grant of a patent or the registration of a utility model or design.

 

 

4 

4 

Summary of Contents for TXP-CLC

























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands