Siemens TXP-CLC Page 157 Manual Download | Manualshive

Page: 157 / 216

background image

TXP CLC Course

11

TXP



SIM Function Block

FB163 MOTVENTR

(Control Motor/Solenoid Valve)

Application

The drive control for motors or solenoid valves can be carried out in the TXP AS
620 B system using the DCM function block FB163 in conjunction with the signal
modules (SIM) in the ET 200M I/O device.

The following input and output signals can be configured for the connection of a
motor or solenoid valve:

RME:

Feed-back message ON/OPEN

RMA:

Feed-back message OFF/CLOSED

SAG:

Switchgear fault

ANB:

Feeder not ready (not racked in)

DE AUF:

Torque Open

DE ZU:

Torque Closed

MTU:

Motor Temperature Monitoring (Motor Operated Valve Only)

ALE:

Output ON/OPEN

ALA:

Output OFF/CLOSED

KV:

Contact power supply

These signals can be input with the vo24 VDC, +115 VDC, 115 VAC,
+230 VDC and 230 VAC (depending on the module used) and output with the
vo24 VDC, 115 VAC and 230 VAC.

Training Center

Copying of this document, and giving it to others and use or communication of the contents, are forbidden without express authority. Offenders are liable to the payment of
damages. All rights are reserved in the event of the grant of a patent or the registration of a utility model or design.

1

«
...
155
156
157
158
159
...
»

Summary of Contents for TXP-CLC

























































































































































































































Reviews:

No comments

Related manuals for TXP-CLC

Brand: Valve Concepts Pages: 16

Brand: Sabaj Pages: 12

Brand: unicore Pages: 25

Brand: unicore Pages: 24

Brand: Samsung Pages: 32

Brand: Aastra Pages: 30

Brand: Manfrotto Pages: 16

Brand: Eaton Pages: 4

Brand: Eaton Pages: 10

Brand: Eaton Pages: 288

Brand: Walimex Pro Pages: 68

Brand: Kamstrup Pages: 36

Brand: JFA Electronicos Pages: 29

Brand: Oceanic Systems Pages: 8

Brand: QUALITY LIFTS Pages: 21

Brand: Uniden Pages: 28

Brand: UniFocus Pages: 23

Brand: UniFocus Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands