Siemens TXP-CLC Page 26 Manual Download | Manualshive

Page: 26 / 216

background image

TXP-CLC

Course

OT

OT

Terminal bus

Terminal bus

AS

AS

Time synchronization throughout DCS
by using Industrial Ethernet

PU

PU

SU

SU

OT

OT

DS

DS

ES

ES

OT/DT

OT/DT

AS

AS

Plant bus

Plant bus

OT/ET

OT/ET

time transmitter

time transmitter

transm

transm

. clock

. clock

every

every

10sec

10sec

GPS/DCF

GPS/DCF

trans

trans

mitter

mitter

In TXP, a system-wide, uniform time is kept by a time transmitter, from which

time-tags are obtained for marking events. The time-of-day is distributed via the

time transmitter over the plant bus.

The time-of-day transmitter is used for time synchronization of the TXP

subsystems AS620, OM650, and DS670 and it transmits time-of-day messages

over the plant bus at intervals of 10 seconds which are received and evaluated

by the connected TXP participants.

The time-of-day transmitter is only implemented on the plant bus; time is

transferred to the participants connected to the terminal bus via the PU. The

time-of-day transmitter can be synchronized via other clocks or it can be used to

synchronize other clocks.

Time-of-day synchronization can also be implemented via one of the

communications processors in the AS620 subsystems (CP1430).

Training Center

Copying of this document, and giving it to others and use or communication of the contents, are forbidden without express authority. Offenders are liable to the payment of
damages. All rights are reserved in the event of the grant of a patent or the registration of a utility model or design.

6

«
...
24
25
26
27
28
...
»

Summary of Contents for TXP-CLC

























































































































































































































Reviews:

No comments

Related manuals for TXP-CLC

Brand: Gardena Pages: 16

Brand: MADRIX Pages: 28

Brand: National Instruments Pages: 29

Brand: LAE electronic Pages: 7

Brand: LAE electronic Pages: 2

Brand: OMA Pages: 53

Brand: NAD Pages: 4

Brand: NAD Pages: 4

Brand: Saftronics Pages: 13

Brand: U-Prox Pages: 3

Brand: TCS Pages: 16

Smart Control Panel 880RGD

Brand: Raynor Pages: 4

Brand: Partizan Pages: 7

Brand: WAC Pages: 5

RC Electronic DPSI LCD

Brand: Emcotec Pages: 32

Brand: GBS Elettronica Pages: 32

Cutler-Hammer S701X25N3BP

Brand: Eaton Pages: 4

Brand: Tescom Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands