Home
/
Siemens
/
TXP-CLC
/
Manual

Siemens TXP-CLC, Manual, Page: 162 / 216

Share

Page: 162 / 216

Siemens TXP-CLC Manual Download Page 162

TXP CLC Course

Command Generation

There are six types of commands:

•

Forcing commands (ignoring enabling permissives and protection)

•

Protection commands (protecting equipment or personnel safety)

•

Commands from a local control unit (at motor or starter)

•

Automatic commands (logic control with enabling permissive)

•

Manual commands (operator control with enabling permissive)

•

Automatic reclosing (after return to normal voltage)

Different enabling criteria, i.e. process enable and manual enable, are required
before a command becomes effective and depend on the type and priority of the
command. With operating mode FORCING, the drive can be operated via the
OM650--commands “Manual ON” and “Manual OFF” irrespective of the process
enable and protection, and automatic commands are blocked. The diagram
below illustrates the priority scheme in the DCM:

Training Center

Copying of this document, and giving it to others and use or communication of the contents, are forbidden without express authority. Offenders are liable to the payment of
damages. All rights are reserved in the event of the grant of a patent or the registration of a utility model or design.

6

«
...
160
161
162
163
164
...
»

Summary of Contents for TXP-CLC

























































































































































































































Reviews:

No comments