Siemens TXP-CLC Page 10 Manual Download | Manualshive

Page: 10 / 216

background image

TXP-CLC

Course

The hierarchical structure of TXP

OT

OT

OT

OT

OT

OT

AP

S5-AG

S5 E/A

FUM-B

FUM-B

Operating and

Operating and

Monitoring Level

Monitoring Level

Group Control Level

Group Control Level

Field Level

Field Level

OM

OM

ES

ES

DS

DS

OT/ET

OT/ET

Processing Level

Processing Level

AP

OT/DT

OT/DT

Individual

Individual

Control Level

Control Level

FUM-B

FUM-B

AP

AP

This figure shows all different and possible components of TXP. Also, it shows
how they are organized in hierarchical structure.

•

The Individual Control Level, at the bottom, is directly connected to the
Field. There are two different configurations for this level: FUM or SIM.

•

The Group Control Level is responsible for the group automation tasks,
coordination of the individual controllers and communication tasks with the
Operating and Monitoring system (OM).

•

The Processing Level processes and stores all signals from the
Automation System and also sends the operator commands to the right
Group Control Level.

•

The Operating and Monitoring Level is the Man-Machine Interface of TXP.
It shows the actual status of the plant to the operator, takes data from the
Processing Level of the System and interprets the orders from operators,
sending this information to the Processing Level.

Training Center

Copying of this document, and giving it to others and use or communication of the contents, are forbidden without express authority. Offenders are liable to the payment of
damages. All rights are reserved in the event of the grant of a patent or the registration of a utility model or design.

4

«
...
8
9
10
11
12
...
»

Summary of Contents for TXP-CLC

























































































































































































































Reviews:

No comments

Related manuals for TXP-CLC

Brand: UCS Pages: 4

Brand: Samson Pages: 32

Brand: Quantum Pages: 15

Brand: Jedia Pages: 12

Brand: JED Micro Pages: 10

Brand: JCM Technologies Pages: 2

disklavier DKC-850

Brand: Yamaha Pages: 2

Brand: V2 Pages: 12

NORA-W10 Series

Brand: u-blox Pages: 56

Brand: z21 Pages: 2

Brand: Zmotion Pages: 48

Brand: Audioaccess Pages: 2

Brand: Nemesis Pages: 6

Brand: HEROSE Pages: 92

Brand: Intermatic Pages: 3

Brand: ACTi Pages: 20

Brand: SOARNEX Pages: 14

Brand: Tristan Auron Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands