Siemens TXP-CLC Page 148 Manual Download | Manualshive

Page: 148 / 216

background image

TXP CLC Course

The signal must be defined (SIGDEF) on the individual level logic diagram
(function plan / YFR) that is identified with the Power Plant Identification Code
(KKS) for the equipment. The signal is then available for use as an output to the
field device. The SIGDEF and KKS must match the output channel identifier in
the parameter mask of the SIM module on the rack level location drawing for the
connection to the output point.
The output signal connection to the hardware from the CAO block must have
YL01 for the I. D. Code designation and the destination on the logic function
diagram (YFR) and a YL01 for the destination ID-code on the module parameter
mask of the SIM binary output module on the hardware diagram (YDR).

Training Center

Copying of this document, and giving it to others and use or communication of the contents, are forbidden without express authority. Offenders are liable to the payment of
damages. All rights are reserved in the event of the grant of a patent or the registration of a utility model or design.

2

«
...
146
147
148
149
150
...
»

Summary of Contents for TXP-CLC

























































































































































































































Reviews:

No comments

Related manuals for TXP-CLC

Brand: EAE Pages: 36

Brand: Samson Pages: 20

Brand: Bang & Olufsen Pages: 9

Brand: Bang & Olufsen Pages: 12

Brand: Hach Pages: 86

Brand: Bard Pages: 8

Brand: Bardiani Valvole Pages: 35

Brand: National Instruments Pages: 2

Brand: S&P Pages: 12

Brand: S&C Pages: 34

Brand: S&C Pages: 32

IntelliCap Plus

Brand: S&C Pages: 32

Brand: S&P Pages: 12

Brand: S&C Pages: 35

Brand: TagMaster Pages: 28

Brand: SYR Pages: 2

Brand: Procom Pages: 10

Brand: ShoreStation Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands