manualshive.com logo in svg

Siemens TXP-CLC, Manual, Page: 158 / 216

Share
Download
Siemens TXP-CLC Manual Download Page 158

 

 

 

 

 

TXP CLC Course

 

 

 
The signals RME, RMA, and SAG can be configured as either a NO or NC 
contact 
 
If the following signals are not wired, the function block reads them as follows: 
 

•

 

SAG = “0” (not faulty) Parameter “RMS” set for NO contact. 

•

 

ANB = “0” (ready or racked in) 

•

 

RME = not RMA 

•

 

RMA = not RME 

 
When Feed-backs are not wired the command outputs are used for the 
generation of the feed-back messages as follows: 
 

•

 

RME = ALE 

•

 

RMA = ALA 

 
Depending on the operating voltages used, the following SIM modules can be 
used in conjunction with the DCM function block: 
 
SIM inputs: 

• 

321-1BL00-0AA0 32 x DC 24V Motor/Solenoid valve inputs 

• 

321-1BH01-0AA0 16 x DC 24V Motor/Solenoid valve inputs 

• 

321-1EH01-0AA0 16 x AC 120V Motor/Solenoid valve inputs 

• 

321-7BH00-0AB0 16 x DC 24V with sensor supply and diagnostics for 
Motor/Solenoid valve inputs 

 
 
SIM outputs: 

• 

322-1BL00-0AA0 32 x DC 24V / 0.5A Motor/Solenoid valve outputs 

• 

322-1BH01-0AA0 16 x DC 24V / 0.5A Motor/Solenoid valve outputs 

• 

322-1HH00-0AA0 16 x REL AC 120V / 0.5A Motor/Solenoid valve outputs 

• 

322-1HF01-0AA0 8 x REL AC 230V / 0.5A Motor/Solenoid valve outputs 

 

Training Center

 

Copying of this document, and giving it to others and use or communication of the contents, are forbidden without express authority. Offenders are liable to the payment of 
damages. All rights are reserved in the event of the grant of a patent or the registration of a utility model or design.

 

2

Summary of Contents for TXP-CLC

























































































































































































































Reviews:

No comments