manualshive.com logo in svg

Siemens TXP-CLC, Manual, Page: 161 / 216

Share
Download
Siemens TXP-CLC Manual Download Page 161

 

 

 

 

 

TXP CLC Course

 

 

 

11

Operating Modes 

 
Operating mode is selected based on the parameters “RMS”, “VBAF”,  “MAUS”, 
“REJ/MAN”, “OP_MODE“; the inputs “VOS”, AUTO”, “MAN”; and the operating 
window buttons of the OM650. 
 
The “SEMI” or semiautomatic mode is selected if the parameter “RMS” is set to 
“TAG OUT NO”.  For any other operating mode, the parameter “RMS” should be 
set to “TAG OUT YES”. 
 
The “VBAF” parameter allows a manual or automatic close command even if the 
DCM block is in an alarm condition. The “REJ/MAN” parameter forces the 
operating mode to manual if manual mode is allowed and the block is in alarm. 
 
The “MAUS” parameter allows a changeover from manual to automatic either 
from the operating window of the OM650 or from the “AUTO” or “MAN” logical 
inputs to the DCM block. 
 
The “OP_MODE” parameter selects between the three options shown below. 
Once an operation mode is selected, the DCM block can only operate in the 
modes named under “Selection”. 
 
OP_MODE 

Selection 

Automatic 
Commands 

Manual 
Commands 

AUTO/MAN Manual 

Automatic 

Deactivated 
Activated 

Activated 
Deactivated 

SEMI/MAN Manual 

Semi-automatic 

Deactivated 
Activated 

Activated 
Activated 

SEMI Semi-automatic 

Activated 

Activated 

 
 
Automatic activated means that automatic commands are effective and manual 
commands are disabled; Semi means that manual and automatic commands are 
effective; and  Manual means that manual commands are functional and 
automatic commands are disabled. The switchover and indication of the 
operating modes “Automatic”, “Semi” or “Manual” is done via the operating 
window of the OM 650 or in the logic. No distinction between the operating 
modes “Automatic” and “Manual” can be made if the TAG-OUT function is not 
activated with the parameter RMS. 
 
The “VOS” input (local control) deactivates all manual, automatic or semi-
automatic commands and allows the feedback to change with local commands 
without initiating alarm conditions. The protection commands are still active. 

Training Center

 

Copying of this document, and giving it to others and use or communication of the contents, are forbidden without express authority. Offenders are liable to the payment of 
damages. All rights are reserved in the event of the grant of a patent or the registration of a utility model or design.

 

5

Summary of Contents for TXP-CLC

























































































































































































































Reviews:

No comments