Siemens TXP-CLC Page 176 Manual Download | Manualshive

Page: 176 / 216

background image

TXP CLC Course

Feeder not ready for operation (ANB)

This binary input can be used to decouple the hardware from the software and
allow modification to the input signal by additional logic before the signal is
connected to the DCM FB 163. When this input is a binary “1” the DCM receives
feedback that the driven device (breaker, switchgear, etc.) is in a test or racked
out condition. It can be used in place of the hardwired input ANB.

Outputs from other logic (not I/O type outputs)
Name Description

CB/ON Actual

status on/open (feedback on)

CB/OFF

Actual status off/closed (feedback off)

DS/ON

Desired status on/open

DS/OFF

Desired status off/closed

ZES

Last status reached by protection

ZEA

Last status reached by automatic

ZEH

Last status reached by manual

USZ

Under voltage time running

ULS

Under voltage limit signal

AZB

Feeder ready for operation

NOSD

No status discrepancy error

NOFF

No feeder fault

KLB

No running time / torque alarm

CB/ONN

Actual status not on/open

CB/OFFN

Actual status not off/closed

VOS Local

controlling

P/SIM PAE_E

simulated

BL/COLO

Command logic locked

CB/AUTO

Feed back priority auto/manual

Feedback on (CB/ON)

This output is a logic “1” when the on feed back input (RME) is energized or the
input FB/ON is a binary “1” and the FB163 has no fault conditions.

Feedback off (CB/OFF)

This output is a logic “1” when the off feed back input (RMA) is energized or the
input FB/ON is a binary “1” and the FB163 has no fault conditions.

Desired status on (DS/ON)

This output is a logic “1” from the time On is requested by logic or by operator,
until feed back On is received or DCM is in a fault condition.

Desired status off (DS/OFF)

This output is a logic “1” ” from the time Off is requested by logic or by operator,
until feed back Off is received or DCM is in a fault condition.

Training Center

Copying of this document, and giving it to others and use or communication of the contents, are forbidden without express authority. Offenders are liable to the payment of
damages. All rights are reserved in the event of the grant of a patent or the registration of a utility model or design.

20

«
...
174
175
176
177
178
...
»

Summary of Contents for TXP-CLC

























































































































































































































Reviews:

No comments

Related manuals for TXP-CLC

ControlMaster CM15

Brand: ABB Pages: 28

Evolution Series E9000

Brand: GE Pages: 44

PACSystems RX7i

Brand: GE Pages: 469

GuardSwitch 300 Series

Brand: GE Pages: 2

GuardSwitch 300 Series

Brand: GE Pages: 2

Masoneilan VariPak 28001

Brand: GE Pages: 24

Brand: Samson Pages: 20

Brand: FrSky Pages: 2

Brand: ECKELMANN Pages: 178

Brand: QUAD Pages: 17

Brand: fadini Pages: 16

Brand: Hanna Instruments Pages: 88

Brand: Lamtec Pages: 22

Brand: Paradox Pages: 32

Brand: Parkside Pages: 86

Brand: QUALITY LIFTS Pages: 21

Brand: VENCO Pages: 44

Brand: Wabtec Pages: 106

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands