manualshive.com logo in svg

Siemens TXP-CLC, Manual, Page: 171 / 216

Share
Download
Siemens TXP-CLC Manual Download Page 171

 

 

 

 

 

TXP CLC Course

 

 

 

11

Total drive run time (TGL) 

Name: TGL 
Function: Defines the total run time of the drive between the limit positions after a 
command output, for alarm and indication (only effective with both RWE and 
RWA set at 3) 
Range of values:   0 to 60,000 
Meaning: 

 

0 = no run time monitoring 
60,000 = 6,000 s (adjusting steps: 0.1 s) 

Default setting:  

10 = 1 s  

 

 

 

Effect of Feed-back message on command execution  

Name: WRBHAEA; WRBHAAZ; WRBSEA; WRBSAZ 
Function: Defines whether  manual, automatic and protection On and Off 
commands are to be blocked when a feed-back fault is active in the command 
direction 
Range of values:   blocked/not blocked 
Meaning: 

 

blocked = blocks command execution 
not blocked = command is executed 

WRBHAEA = MANUAL/AUTOMATIC ON blocked/not blocked  
WRBHAAZ = MANUAL/AUTOMATIC OFF blocked/not blocked 
WRBSEA = PROTECTION ON blocked/not blocked 
WRBSAZ = PROTECTION OFF blocked/not blocked 

Basic setting: blocked 
 

Effect of status discrepancy/monitoring  

Name: WEFSPERR; WEFNSEA; WEFNSAZ 
Function: Defines whether limits are monitored and if the protection On and Off 
commands should be blocked when a status discrepancy fault is detected 
Range of values: blocked/not blocked 
Meaning: 

WEFSPERR = blocked status discrepancy monitoring disabled 
WEFSPERR = not blocked status discrepancy monitoring enabled 

WEFNSEA = PROTECTION ON command blocked/not blocked 
WEFNSAZ = PROTECTION OFF command blocked/not blocked 

Basic setting: blocked

  

 
Slowing-down time for travel-dependent disconnection (NLZ) 

Name: NLZ 
Function: Defines how long the command output signal is maintained after the 
feedback input signal is received for torque close or open. 
Range of values:   0 to 100 
Meaning: 

 

0 = no delayed disconnection 
100 = 10 s disconnection delay 

Basic setting:  

0 

Training Center

 

Copying of this document, and giving it to others and use or communication of the contents, are forbidden without express authority. Offenders are liable to the payment of 
damages. All rights are reserved in the event of the grant of a patent or the registration of a utility model or design.

 

15

Summary of Contents for TXP-CLC

























































































































































































































Reviews:

No comments