manualshive.com logo in svg

Siemens TXP-CLC, Manual, Page: 21 / 216

Share
Download
Siemens TXP-CLC Manual Download Page 21

 
 

  

 

TXP-CLC 

Course

 

 

 

3 

TXP Industrial Ethernet 

 

CP

CP

CP

CP

CP

CP

CP

CP

CP

CP

SIMATIC S5

SIMATIC S5

AS

AS

Communication without limits using the
Industrial Ethernet  local area network

WAN

WAN

Industrial Ethernet

Industrial Ethernet

Industrial

Industrial

Ethernet

Ethernet

bridge

bridge

OM

OM

gateway

gateway

ES

ES

 

 

The AS620, OM650, and ES680 subsystems of TXP are interconnected via the 
bus system Industrial Ethernet, which features the following advantages: 
 

•

 High 

availability 

•

 Single-fault 

tolerance 

•

 Standardized 

protocol architecture in accordance with ISO/OSI 

•

 

Ability to use the optimum transfer medium (drop cable, twisted pair, or 
fiber-optic cable) 

•

 High-performance 

transfer rate (100/10Mbit/s) 

•

 

Support for the use of redundant TXP participants 

•

 

Bus management and diagnostics functions 

•

 

Scale-ability with respect to plant size 

•

 

Wide area coverage 

•

 

Bridges, which are used for: 

 

•

 implementing 

backbones 

•

 

connecting to other networks 

•

 increasing 

coverage 

•

 safety 

de-coupling 

•

 load 

de-coupling 

•

 WAN 

coupling 

Training Center 

Copying of this document, and giving it to others and use or communication of the contents, are forbidden without express authority. Offenders are liable to the payment of 
damages. All rights are reserved in the event of the grant of a patent or the registration of a utility model or design.

 

1

Summary of Contents for TXP-CLC

























































































































































































































Reviews:

No comments