Siemens TXP-CLC Manual Download Page 23 | Manualshive

Page: 23 / 216

Siemens TXP-CLC Manual Download Page 23

TXP-CLC

Course

3

Industrial Ethernet Bus System design and mode of
operation

virtual ring

virtual ring

CP

AP

AP

CP

AS

AS

CP

PU

PU

CP

OM

OM

AP

AP

CP

AS

AS

Starcoupler

Starcoupler

Starcoupler

Starcoupler

Starcoupler

Starcoupler

Fiber Optic Cable

The central components of the Industrial Ethernet bus are star couplers that are

connected together via optical paths to form a ring, which is referred to as the

virtual ring.

The bus itself, that is the link between the star couplers, is implemented with an

optical transfer medium. The participants are connected to the star coupler via an

electrical transfer medium or a combined electrical and optical transfer medium.

Training Center

Copying of this document, and giving it to others and use or communication of the contents, are forbidden without express authority. Offenders are liable to the payment of
damages. All rights are reserved in the event of the grant of a patent or the registration of a utility model or design.

3

«
...
21
22
23
24
25
...
»

Summary of Contents for TXP-CLC

























































































































































































































Reviews:

No comments