Siemens TXP-CLC Page 110 Manual Download | Manualshive

Page: 110 / 216

background image

TXP CLC Course

Signal TTD

Time-tagged data result as a signal TTD (i.e. exception report) following a
change in status of the input signal (whether binary signal of Process Image
Input Table or simulation value from the Simulation Data Block) if the parameter
TTD is set to “1”.

The following signal TTDs are generated:

•

Change in input signal

•

Channel

is

simulated

•

Channel

is

valid/invalid

A signal connection to the Operating and Monitoring System (OM) must have a
destination ID code defined as YP01 and a destination defined as YP01. The
signal will then be connected to the Archive, Alarm Summary and can be
connected to individual operator graphics.

In addition to selecting a signal to be a TTD, the class of alarm to be generated
can also be selected using the AWT parameter. The following event classes are
available:
E

Event (will not show up in ASD, only in archive)

A

Alarm or trip (notifies operator that something has already tripped)

W

Warning (notifies operator that immediate action needs to be taken)

T

Tolerance (a tolerance limit has been exceeded)

L

Local fault (indicates that a non-critical fault has occurred; i.e. “tank level
high” in the case of automatic tank overflow)

M

Maintenance and service (indicates that a maintenance or service activity
is necessary)

C

Change (indicates a change in status of a pre-defined switching; i.e.
“changeover to spare pump”)

The direction of the TTD to be generated can also be configured using the REV
parameter. With REV set to “0” the TTD will be direct acting, i.e. logic “1” will
generate a TTD. With REV set to “1” the TTD action will be inverted, i.e. a TTD
will be generated on a logic “0”.

Training Center

Copying of this document, and giving it to others and use or communication of the contents, are forbidden without express authority. Offenders are liable to the payment of
damages. All rights are reserved in the event of the grant of a patent or the registration of a utility model or design.

8

«
...
108
109
110
111
112
...
»

Summary of Contents for TXP-CLC

























































































































































































































Reviews:

No comments

Related manuals for TXP-CLC

Brand: Vacon Pages: 6

Brand: Vacon Pages: 24

Brand: Vacon Pages: 30

Brand: Vacon Pages: 81

Brand: Vacon Pages: 17

Brand: Vacon Pages: 100

Brand: Game ready Pages: 24

Brand: BlitzRotary Pages: 41

Brand: Hunter Pages: 2

Brand: Triadis Pages: 4

Brand: jablotron Pages: 12

VEGACAP 60 Series

Brand: Vega Pages: 12

Brand: D+H Pages: 17

Ratio Feeder J+ Advanced Series

Brand: H.E. Anderson Pages: 11

Brand: A & H Pages: 35

Brand: Cypress Pages: 2

MEMO CORE CONTROL

Brand: MegaLite Pages: 11

Brand: Bard Pages: 102

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands