Siemens Hipath bizip 410 Administration Manual Download Page 24

Page: 24 / 144

Getting started

Updating the firmware on your BizIP 410 telephones

HiPath BizIP is continuously under development. For this reason, you
should update the firmware on the BizIP 410 telephones before using
them for the first time. Proceed as follows:
1. Start up HiPath BizIP with all connected telephones

Page 13. En-

sure that a connection to the Internet exists.

2. Open the HiPath BizIP administration interface

Page 18 on the PC

and click
>

System-wide Settings

FTP Downloads - All Phones

3. Enter the following data (if not already specified):

–

FTP Server Address

: 194.138.17.200 (or bizip.siemens.com)

–

FTP user name

: (empty

–

FTP password

: (empty)

–

FTP path

: HiPath_BizIP1.0

–

Application download filename - Adv

: 410a.app

–

Application download filename - Eco

: 410e.app

–

Action on submit

: Download application

4. Click

Submit

. Once you have done this, all phones will be updated

within a few minutes.

Further information on updating HiPath BizIP is available starting on

Page 88.

Summary of Contents for Hipath bizip 410

















































































































































Search results

Summary of Contents for Hipath bizip 410

Reviews:

Siemens Hipath bizip 410, Administration Manual, Page: 24 / 144

Search results

Summary of Contents for Hipath bizip 410

Reviews: